Carrier 33ZCVAVTRM Spezifikationen Seite 129
- Seite / 316
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3
Mount PremierLink™ Control
LOCATION — The PremierLink controller should be
located inside one of the available service access panels of the
unit. Be sure the location selected prevents moisture and
rain from coming into contact with the circuit board.
Select a location which will be safe from water damage and
allow sufficient access for service and wiring. For service
access, there should be at least 6 in. of clearance between the
front of the PremierLink controller and adjacent surfaces. Be
sure to leave
1
/
2
-in. clearance in front of RJ-14 connector for
attaching RJ-14 cable from a CCN interface device. A field-
supplied right angle 6-pin RJ-14 connector can be attached if
necessary.
NOTE: If the PremierLink controller must be installed in a
location where there is not easy access to CCN connectors,
a remote connection kit (part number 33CSREMCCN) can
be ordered.
MOUNTING — Refer to Mounting Sheet included with
controller for additional detailed mounting instructions.
1. Ensure all power to unit is removed.
2. Locate a space in the unit control panel or a space inside
the equipment that is free from dirt and dust.
3. Remove plastic cover by gently squeezing the middle of
longer sides of the cover and pull away from the board.
This will release the locking tabs inside.
4. Mount the PremierLink controller to the desired location
by holding the controller firmly in place. Be sure all
standoffs are in contact with mounting surface and board
DOES NOT flex! Attach controller to unit using 4 screws
provided ensuring a secure grip to unit surface.
See Fig.1.
NOTE: If PremierLink controller will be installed in same
location where Apollo controller was previously installed,
simply use 2 of the existing Apollo mounting holes to line up
with the board.
5. Provide 24 v power to the circuit board from the unit
transformer or an isolated power transformer. Use the
appropriate conductors for voltage per base unit name-
plate. See Fig. 2. Board will require 10 va at 24 vac.
6. Replace plastic cover to protect circuit board.
7. Restore power to unit.
PremierLink Controller Inputs and Outputs —
The PremierLink controller inputs and outputs are shown in
Table 1.
Control Wiring — The PremierLink controller can be
connected to either a Carrier-approved thermostat or CCN
compatible temperature sensor.
1. Turn off power to the control box.
2. Strip the ends of the red, white, and black conductors of
the communication bus cable.
NOTE: When connecting the communication bus cable, a
color code system for the entire network is recommended to
simplify installation and checkout. See Table 2 for the
recommended color code.
Disconnect electrical power before wiring the Premier-
Link controller. Electrical shock, personal injury, or
damage to the PremierLink controller can result.
Fig. 1 — PremierLink Control Module
a33-9129
- Specification 1
- Mount Bypass Controller 6
- Dimensions in ( ) are in mm 9
- START-UP 16
- Display Units F 21
- 0.0 dF TEMP_CAL 21
- OPERATION 22
- System Pressure Operation 22
- Tab 1 1 a 1 3 a 24
- Features/Benefits (cont) 26
- Field-installed accessories 27
- Override 32
- Transformer ground 34
- Chassis Ground 34
- ZC — Zone Controller 48
- 24VAC/DC 50
- (IF USED) 52
- FIELD-SUPPLIED 53
- DRY CONTACT 53
- Perform System Checkout 54
- CONFIGURATION TABLES 57
- pressure and other 58
- as loading conditions on 60
- slidebar information 63
- 2.0 ^F SET_LIMT 66
- 2.0 ^F LOADLIMT 66
- MAINTENANCE TABLES 68
- System Mode Selection — 79
- → 3V™ System Mode Selection 83
- 3V™ Zone Damper Operation 84
- Limit such that: 86
- Table of contents 90
- VVT® system key components 91
- Dimensions (cont) 94
- Performance data 96
- Performance data (cont) 98
- Application data 99
- Application data (cont) 100
- (Locate upstream of damper) 101
- 2) and maximum 110
- 2 (if applicable) 110
- Features/Benefits 114
- Accessories 115
- Specifications 115
- Accessories (cont) 116
- Dimensions 116
- Installation Instructions 117
- CONNECTOR 118
- (PLUG-IN TYPE 118
- Communication Connections 120
- Related Documentation 120
- Smoke Control Applications 121
- CCN Bus Supervisor 122
- Comfort Controller 6400 123
- PRODUCT DATA 124
- Comfort Controller 6400-I/O 125
- Installation, Start-Up and 127
- Configuration Instructions 127
- INSTALLATION 128
- Inspection — 128
- Mount PremierLink™ Control 129
- 50HJQ014,016 UNITS 131
- FIELD WIRING 133
- Factory Wiring 135
- Field Wiring 135
- COVER REMOVED SIDE VIEW 138
- OA — Outdoor Air 141
- OAT — Outdoor Air Temperature 141
- MANUFACTURER CABLE PART NO 142
- Alpha 2413 or 5463 142
- American A22503 142
- Belden 8772 142
- Columbia 02525 142
- LEGEND 145
- N/C — Normally Closed 145
- N/O — Normally Open 145
- C7400A1004 146
- ACTUATOR 150
- 50TJ400812 150
- M9206-GGC-2 150
- Check-Out 151
- O) when occupied 154
- CONFIGURATION 157
- 0.0 ^F STO 158
- 2.0 ^F LIMT 165
- Rev Valve Heat Mode Cool Mode 167
- Heat ON OFF 167
- Cool OFF ON 167
- Book 1 4 178
- Tab 11a 13a 178
- Universal Controller 191
- Introduction 193
- About this Manual 195
- Numbers Specifications 196
- Overview 196
- 8 Inputs 196
- Features 197
- 8 Outputs 197
- Figure 1 199
- InstallationandWiring 201
- Installation and 203
- Panel Mounting 204
- Wall Mounting 205
- DIN Rail Mounting 206
- Power Wiring 207
- System Pilot 207
- Installation 207
- Power Supply 207
- Figure 5 208
- Power Connector Location 208
- Power Connector Pin 208
- Assignments 208
- Communication 209
- Grounding of Bus 210
- Figure 7 211
- CCN Communication Wiring 211
- Figure 8 212
- Communication Connector 212
- Location 212
- Sensor and Device 213
- General Input 214
- Sensor Wiring 214
- Externally Powered 215
- 4-20 mA Sensor Wiring 215
- Wiring T-56 Space 216
- Temperature Sensor 216
- Wiring ACI 10K-AN 216
- Configuration 217
- Guidelines 217
- Checkout 219
- Diagnostic LEDs 222
- External Devices 223
- Module Operation 223
- Additional Temperature to 227
- Resistance Conversions 227
- Input and Output 228
- Connection 228
- Tuning Control 229
- Definition of Terms 230
- Equations 231
- System Checkout 232
- Determination of 234
- Throttling Range 234
- Dual Loop PID Tuning 234
- Single Loop PID Tuning 238
- Appendixes 241
- Wire List 243
- Appendix B 245
- Figure 18 246
- Button for Clearing the 246
- Database 246
- Appendix C 247
- Item Value Comments 248
- Table C-1 248
- Quick Reference Guide 248
- (Continued) 248
- Reader's 257
- Comments 257
- Carrier Corporation 258
- One Carrier Place 258
- Farmington, CT 06034-4015 258
- Attn: CCN Documentation 258
- INSTALLATION 266
- General — 266
- Zone Controller Hardware — 266
- Field-Supplied Hardware — 266
- Mount Zone Controller 268
- ZONE Controller 269
- Connect Airflow Pickups — 271
- HF23BJ042 272
- Install Sensors 283
- Cool Warm 285
- BLK (GND) 285
- RED (SPT) 285
- Zone Controller 288
- Remote Occupancy Contact — 290
- Connect the Outputs — 290
- Perform System 293
- Check-Out 293
- Network Addressing — 294
- Initial Operation and Test — 294
- Airflow Check — 294
- Points Display Screen — 295
- Default Value 1 299
- 0 cfm OFFSET 303
- 2 F LIMT 305
- — This configuration deter 306
- 0 cfm SOFFSET 306
- Units cfm 307
- airflow 312
- Minimum Cooling 312
- Heat Master 314
- Ta b 11 a 1 3 a 316
Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Carrier 33ZCVAVTRM
(16 Seiten)
(160 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.627 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern